| Click to Post a New Message!
Page [ 1 ] |
|
|
Designer Sheds
Somebody mentioned "designer" plans for sheds, and the desire of some folks to have something a bit difrerent.
Along those lines, I built an octagonal shed for my sheep, with a small cupola. I prefabbed the sections, and tipped them up and spiked them together. Very easy to build, and something a bit different.
Check the link for pictures.
Link:  
|
|
Add Photo
Bookmarks: |
|
|
|
Designer Sheds
Heh, heh, heh...
That's The Grumpasaurus. She keeps the ram away so I can bend over and pound nails without looking over my shoulder all the time... ":^)
|
|
Add Photo
Bookmarks: |
|
|
|
Designer Sheds
"Plans" came right out of my pointy little head. Not significantly more difficult to build than an ordinary shed. I don't recall the diameter, I'd have to run down and measure to be sure, but it's either 12 or 15 feet between opposite panels. Basically I staked out the octagon, stood inside the "circle", looked around and said, "Yeah, that looks big enough". First layout was too small. Also gave some consideration to the length of each segment. Original idea was for 4' segments, but that made it too small. I think the panels are a tad over 5' as shown.
Next step was to get the "foundation" in place. Cut the bottom sills out of 2x8 treated lumber. Using this as a pattern, placed, butted and leveled cement blocks. Then I laid the 2x8 over and drilled holes in the board centered over the outermost cells of the blocks to put J bolts in for anchors. Drilled smaller holes over each cell in the rest of the blocks. Then I poured concrete in each cell of each block, put J bolts in the outer cells, set the boards down over, and put BIG galvanized spikes (that I had layijng around from a scrounging mission) in each of the center cells. This ties all the blocks together and keeps them from kicking out. The whole thing floats on top of the ground.
The 7 panels I prefabbed in the shop. I ripped 22.5 degree bevels on the outside of the end studs, other than that, normal procedures.
Roof was not bad, just butted the first two rafters together and nailed them. Next two rafters butted to them at 90 degrees. Then cut 4 more rafters with a V shaped end and butted and nailed into the intersections of the first four. Then cut blocking to make the small octagon up near the peak, and the last 8 rafters butt to them. Did make one mistake here, when I cut the rafter tails. I cut each one a fixed distance from the wall. That meant that the one in the center of each panel was slightly longer than the ones at the ends of the panel. This made decking the roof more difficult that it should have been. Next time, I'll cut the ones at the corners of the panels to length, then snap a line between them to cut the center one to length.
Lots of extra waste when shingling, due to the angle cuts at each joint in the roof. Had to make two extra trips for shingles.
It was fun to build, it's visually attractive, and it's been plenty rugged, even though it's framed completely with 2x4's, less the sills over the blocks. Yup, if I needed another shed, I'd do it again. In fact, on a slightly smaller scale, it'd make a nifty garden shed. Lots of places to hang tools...
|
|
Add Photo
Bookmarks: |
|
|
|
Designer Sheds
Oddly enough, I do raise a few turkeys. They're on the other side of the pasture in a little rectangular building.
|
|
Add Photo
Bookmarks: |
|
| |
|
Page [ 1 ] | Thread 34476 Filter by Poster: 1 | 1 | 4 | 2 |
|
()
Picture of the Day DennisCTB
Unanswered Questions
Active Subjects
Hot Topics
Featured Suppliers
|